Wax Print Fabric Widths: 115cm vs 120cm vs 150cm and What They Do to Your Cutting Yield

Three wax print fabric roll widths: the wider roll costs more per meter but often less per finished garment.

Two mills quote the same wax print pattern at the same price per meter, and the cheaper quote still loses money for the buyer. Why? Because wax print fabric width decides how many panels fit across the cloth, and that number decides how many meters leave your cutting table with the order. Therefore, a buyer who compares only the price per meter compares the wrong number.

This article works through the three widths that dominate wax print quotations — 115 cm, 120 cm and 150 cm — and shows what each one does to yield, waste and true cost. Every figure below is an illustrative assumption inside my own example, so you can repeat the arithmetic with your own prices.

Why Wax Print Fabric Width Cannot Simply Be Stretched

A wax print mill does not choose width freely. The loom weaves to a fixed reed width, and the rotary screen printing line prints a fixed repeat field across it. Consequently, the loom and the print screen set the ceiling, and the selvedge sets the trim. A mill running a 115 cm print cannot stretch that same screen to 150 cm; wider cloth needs a different loom setup and different screens. Meanwhile, buying habits pull the trade toward a handful of standard widths: traders cut 6-yard wrappers, tailors cut single panels, and home-textile buyers cut wide bedding.

The Three Widths and Where Each One Belongs

Width behaves as a package: the wider the cloth, the higher the price per meter and the lower the waste on wide panels. Buyers who order 115 cm wax print fabric accept a longer marker in exchange for the lowest price per meter, while a 150 cm African print fabric pairs wide panels in a single band. Notice the column that decides the outcome below: nominal width never reaches the cutting table.

Width Usable width after trimming selvedges (illustrative) Where buyers use it The trade-off
115 cm About 113 cm 6-yard wrappers, tailoring, narrow single-panel garments Lowest price per meter; highest marker length on wide panels
120 cm About 118 cm Wrapper-and-blouse sets, general garment programs Slight yield gain over 115 cm; rarely enough to re-plan a marker
150 cm About 148 cm Wide garments, two-panel layups, bedding and home textiles Highest price per meter; often the lowest cost per usable square meter

Selvedge, pin holes and printed edge eat 1–2 cm on each side, so a 150 cm roll delivers roughly 148 cm of usable cloth. Subsequently, every yield calculation starts from usable width, not from the label.

The Only Fair Comparison: Cost per Usable Square Meter

Because a meter of 150 cm cloth carries more fabric than a meter of 115 cm cloth, price per meter misleads, and the ranking can flip once you convert. Measure the roll itself under ISO 22198, which specifies how to determine the width and length of relaxed fabric, and measure mass per unit area with the method in ISO 3801 when you compare weights.

Quote Price per meter Usable width Area per meter Cost per usable m²
A — 115 cm roll $2.20 1.13 m 1.13 m² $1.95
B — 120 cm roll $2.35 1.18 m 1.18 m² $1.99
C — 150 cm roll $2.85 1.48 m 1.48 m² $1.93

Those prices are illustrative. Even so, the logic holds: quote C looks 30% dearer per meter and proves the cheapest per square meter of usable cloth. However, cost per square meter still does not settle the decision, because a marker rarely uses every square centimeter. The layout does.

How Wax Print Fabric Width Changes Cutting Yield

Take a panel set from one garment: two main panels at 70 cm wide and 100 cm long, two sleeves at 55 cm wide and 60 cm long, and one facing at 40 cm wide and 50 cm long. Markers must lay whole panels side by side across the usable width, and each band runs as long as its tallest panel. That single figure therefore sets the fabric width cutting yield for the whole order.

Usable width Bands the marker needs Total marker length Fabric consumed
113 cm (from 115 cm) Main panel alone; main panel alone; two sleeves together; facing alone 100 + 100 + 60 + 50 cm 310 cm
118 cm (from 120 cm) Main panel alone; main panel alone; two sleeves together; facing alone 100 + 100 + 60 + 50 cm 310 cm
148 cm (from 150 cm) Both main panels together; two sleeves together; facing alone 100 + 60 + 50 cm 210 cm

Here is the lesson that surprises buyers. The 5 cm step from 115 cm to 120 cm changes nothing in this layout, because 70 + 70 cm still exceeds both usable widths. By contrast, the jump to 150 cm pairs the two main panels in a single band and removes 100 cm from every garment. Therefore, wax print fabric width pays off in steps rather than in centimeters. Add pattern repeat matching, shrinkage and cutting waste on top, and the gap widens again — our walkthrough of fabric consumption and cost per garment runs the full formula with a printed dress and a bedding set.

Tolerance, Selvedge and Shrinkage: The Fine Print Behind Width

Width arrives with a tolerance, and a vague purchase order invites a dispute later. Agree the number in writing — ±2% on nominal width, for example — and name the measurement method. Three effects then chip away at width before the cutting table sees it:

  • Selvedge trim. Pin holes, printed edge and thick selvedge take 1–2 cm per side, so a 115 cm roll rarely delivers more than 113 cm to the marker.

  • Shrinkage. Cloth contracts in width as well as in length. Test to ISO 6330, which defines the domestic washing and drying procedures, and treat the post-wash width as the working number for garment programs.

  • Finish width versus printed width. Finishing and heat setting can pull the cloth back slightly, so measure the finished roll on arrival.

Moreover, width interacts with the print. A design with a broad repeat forces the marker to round up to a whole repeat, which costs extra length no matter how wide the roll. Our guide to wax print fabric weight covers how grams per square meter and repeat size work together when you match a base cloth to a design.

Roll Diameter, Loading and the Square-Meter View

Width changes how the order travels. At the same roll length, wider cloth makes a larger roll, so a container holds fewer rolls while each carries more square meters. Consequently, compare total usable area per container, not roll count.

How to Write Width into a Wax Print Purchase Order

Put these eight lines in the order, and the width argument disappears:

  1. Nominal width and usable width, stated as two separate numbers.

  2. Width tolerance, with the measurement method named (for example, ISO 22198).

  3. Selvedge standard: trimmed or untrimmed, and the maximum acceptable pin-hole depth.

  4. Shrinkage test standard and the post-wash width you expect.

  5. Grams per square meter with its tolerance, measured to a named method.

  6. Roll or piece format: continuous roll, cut length or 6-yard pieces, with a length tolerance.

  7. Packaging: roll diameter limit, bale count and labeling.

  8. Layout drawing: the marker plan your width implies, on the panels you intend to cut.

Meanwhile, keep the approval sample. When a second order arrives with cloth 3 cm narrower, that retained piece settles the discussion in an hour instead of three weeks.

Where Weifang Tianhong Fits

Weifang Tianhong Textile has run an integrated chain from texturing to printing, dyeing, cutting and sewing since 2002 in Weifang, Shandong. Because one team owns the loom, the print line and the cutting table, width stops being a compromise between departments.

  • 600 water-jet and 150 air-jet looms let us weave to the width your marker wants instead of forcing your marker onto our stock width.

  • Eleven printing and dyeing lines — nine pigment and two reactive — print the field your order needs, with an in-house laboratory confirming shrinkage and width before the bulk run.

  • Free A4 samples in 1–3 days let you check hand, weight, print and usable width before you commit meters.

  • Orders from 60 yards, with regular cloth shipping in 7–10 days and custom-woven cloth in 15–25 days, paid by T/T, L/C, D/P or Western Union.

Ready to fix your width? Request a width and yield estimate with your panel list, or browse our wax print fabric range and the fully customizable African wax fabric program. We answer on WhatsApp at +86 18953683988 and by email at wftianhong@gmail.com.

FAQ

Does a wider wax print fabric always cut my cost per garment?

No. A wider roll pays off only when the marker pairs panels side by side. In the example above, the 115 cm and 120 cm rolls consumed the same 310 cm, because the two 70 cm panels never fitted together. The 150 cm roll cut that to 210 cm. Ask for the layout drawing first.

What is the difference between nominal width and usable width?

Nominal width is the figure on the label. Usable width is what reaches the marker after you trim selvedge, pin holes and printed edge, which usually removes 1–2 cm per side. Write both numbers into the purchase order.

Which width should I order for 6-yard wrappers?

Wrapper programs usually run on 115 cm and 120 cm cloth, because the piece length matches the wrapper rather than the roll width. Send the wrapper dimensions and the fold you sell, and we return a width recommendation with the piece count per bale.

How much width tolerance should I accept?

Agree the figure in writing and name the measurement method. A tolerance of ±2% on nominal width appears in many wax print contracts, and the retained approval sample decides any dispute. Measure in a relaxed state, never under tension.

Will the width change after washing?

Yes. Cloth contracts in width as well as in length, so a garment program needs a wash test under ISO 6330 and a post-wash width on the specification sheet. Buyers who skip the test usually discover the difference when finished pieces no longer fit the pattern.

Final Thoughts

Price per meter is a comfortable number and a misleading one. Convert each quotation into usable square meters, run one marker layout across the widths you are offered, and the choice usually makes itself. Send your panel sizes, and we will return the marker length, the usable width and the cost per finished garment.