The corner carries the load: pocket depth, seam construction and elastic together decide whether the sheet stays on.
Bedding complaints rarely start with the fabric. They start at the corner, where a sheet grips the mattress or springs off during the first night. Consequently, fitted sheet specifications belong in three places — the depth you cut, the corner you sew, and the elastic you choose — not in the GSM column alone.
This article works through those three decisions, building on the depth figures our 2026 bedding sourcing handbook lists, and showing how to engineer a sheet that still meets them after a wash.
Pocket Depth Is Three Numbers, Not One
Buyers usually quote a single depth and assume the mill understands it. In practice, three numbers govern the fit: the flat mattress depth the sheet must cover without stretching, the maximum depth it must still accommodate over a topper, and the tuck-under allowance beneath the mattress.
Confuse the second with the first, and the sheet fits the sample mattress but fails on the deeper model in the same range. Therefore, write both and treat the tuck-under as its own line.
Treat those figures as an illustrative band for your own testing, because mattress construction and corner radius vary by market.
Corner Construction: Where the Sheet Actually Fails
The corner square you cut must cover the mattress depth, the tuck-under, the elastic hem and the seam allowance. Add shrinkage, and it grows.
Here is the arithmetic for a 30 cm mattress:
Consequently, the cutting room removes a 48 cm square from each corner, not the 30 cm a buyer might picture from the words “30 cm mattress”.
Whichever corner you choose, reinforce the seam that takes the strain: bartack where the elastic meets the gusset seam, set stitch density from your own laundering trial, and specify the thread.
Elastic Choice Changes the Fit More Than the Fabric Does
Elastic decides how a sheet behaves on the second corner, not just the first. Four configurations cover the market, and each one fails differently.
Within each configuration, three variables carry the performance: elastic width, elastomer type and tension. Wider elastic spreads pressure and resists roll-over, which matters on deep pockets where a narrow tape concentrates load on the seam. Meanwhile, tension trades against reach, because very tight elastic shortens the effective pocket depth and makes the sheet hard to fit.
Test the elastic rather than trusting a description. ASTM D4964 covers tension and elongation of elastic fabrics, and the trade uses the method for acceptance testing of commercial shipments. Two of its notes belong in your purchase order. First, the loop tension and extension relationship judges whether an elastic suits a given end use. Second, results compare only when the testing machine, rate of extension, maximum loading and specimen specification match, so name the set-up before testing and report it with the results.
Add one more line, because elastic ages: the standard also requires both parties to agree the laundering temperature and the number of wash and dry cycles before any wash-related testing. That agreement turns “the elastic snapped” into a measurable claim.
Shrinkage: Size the Sheet So the Pocket Still Fits After Washing
A fitted sheet contracts in both directions, and the pocket depth shrinks with it. Therefore, build the cut size from the finished requirement, not from the mattress alone.
Work the sum backwards: divide each finished dimension by one minus the shrinkage rate. For a sheet that must finish at 203 cm with 4% shrinkage, cut 203 ÷ 0.96 = 211 cm, then apply the same logic to the corner square.
Name the test procedure as well, because the result depends on how you wash and dry the sample. ISO 6330:2021 defines a complete test as one washing procedure plus one drying procedure. It offers 16 washing procedures for horizontal-axis front-loading machines, 12 for top-loading agitator machines and 7 for top-loading pulsator machines, plus six drying options that include line dry, flat dry, flat press and tumble dry. The standard also warns that machine type, detergent and dryer change the result.
Consequently, a supplier who quotes shrinkage without naming the procedure leaves you nothing to compare. Write the machine type, detergent and drying method into the specification, then hold bulk to the same route.
The Four-Corner Fit Test Before Bulk
Flat-fabric photography hides every corner problem a fitted sheet can have. Instead, build the sample over a mattress form at the stated maximum depth and photograph it.
Above all, keep the approved sample and its measurements, so a repeat order has a physical reference and a fit dispute has evidence.
Hotel and Healthcare Programs: Care Labels Do Not Cover Industrial Laundry
Hospitality buyers often assume the care label answers the laundering question. It does not. ISO 3758:2023 covers domestic washing, bleaching, drying and ironing, plus professional dry and wet cleaning — while excluding industrial laundering. The same standard notes that industrial laundering symbols appear in ISO 30023.
The standard also excludes non-removable mattress and upholstered furniture covers, since those products need cleaning processes it does not describe. Therefore, a hotel program needs its own wash-life specification for pocket depth and elastic retention, tested over a stated number of cycles.
What to Write in the Fitted Sheet Purchase Order
-
Mattress dimensions: width, length, and both the flat depth and the maximum accommodated depth.
-
Pocket depth: the finished depth, not the cut depth.
-
Tuck-under allowance: stated separately.
-
Corner type: boxed, gathered, split or envelope.
-
Elastic specification: configuration, width, elastomer type, plus the test method and the set-up reported with results.
-
Elastic durability: tension retained after an agreed wash cycle.
-
Shrinkage: a maximum percentage, tested per a named procedure with the machine type and drying method.
-
Seam specification: stitch density, reinforcement at the corner, and thread type.
Where Weifang Tianhong Fits
Weifang Tianhong Textile has produced bedding in Shandong since 2002, and runs weaving, dyeing, printing, finishing and sewing under one roof.
-
300 sewing machines and 50 cutting units produce about two million bedding sets a year, which keeps fitted-sheet construction consistent.
-
An in-house physical testing laboratory checks shrinkage, fastness and tensile properties against AATCC and ISO methods, so a pocket depth claim comes with a measurement.
-
Custom combinations across fitted sheets, flat sheets, pillowcases and duvet covers, with the pocket depths your program needs.
-
Free A4 swatches of your chosen fabric before you commission a fitted sample.
-
Realistic timing: sampling adds 7–15 days, and a bulk run takes 25–40 days after approval.
Building a fitted sheet program? Send your mattress chart, depths and target wash regime and we will return a construction spec with the corner square, elastic spec and shrinkage route. Browse the bedding set or bed sheet fabric range first. We answer on WhatsApp at +86 18953683988 and by email at wftianhong@gmail.com.
FAQ
What pocket depth should I order for fitted sheet specifications?
Order from your customer’s mattress, then add tuck-under. For a 30 cm mattress, a finished depth near 36 cm with a 10 cm tuck-under holds well, and the corner square reaches roughly 48 cm once you add the hem, seam and shrinkage allowance.
Why does my fitted sheet keep coming off one corner?
Three causes dominate: a pocket depth below the maximum mattress depth, a tuck-under too short to hold friction, or relaxed elastic. Check the depth against the deepest mattress in the range before you blame the elastic.
Which is better, four-corner elastic or full-perimeter elastic?
Four-corner elastic suits standard retail sizes and costs less, while full-perimeter elastic grips better on deep mattresses and mixed bedding. For pockets above 35 cm, full-perimeter elastic at 15 mm or wider earns the extra cost.
How do I specify bed sheet elastic so it survives commercial laundry?
Name the configuration, width, elastomer type and test method, then agree a wash regime with your supplier. ASTM D4964 requires both parties to agree the laundering temperature and cycle count before wash-related testing, which gives the tension figure a defined meaning.
Does fitted sheet shrinkage affect the pocket depth?
Yes, in both directions. Divide the finished requirement by one minus the shrinkage rate to reach the cut size, then apply the same allowance to the corner square. Test with a named procedure, because ISO 6330 notes that machine type, detergent and drying method change the result.
Final Thoughts
Fitted sheet specifications live or die at the corner. Write the maximum mattress depth, cut the corner square with tuck-under and shrinkage included, choose elastic against a named test method, and prove the fit on a mattress form rather than flat fabric. Send your mattress chart and wash regime, and we will return the construction spec behind the price.

